Bionaire Fan BSF1731 User Manual

osc illating  
STAND  
fan  
fan  
rem ote c ontrol  
STAND  
MODEL BSF1731  
BSF1731RC  
BSF1731RC-CN  
Read instructions before operating. Retain for future reference.  
Instruction Leaflet  
IN FO-LIN E  
☎
If after having read this leaflet, you have any questions  
or com m ents on your fan,  
call 1-8 0 0 -7 8 8 -5 3 5 0 in North Am erica.  
428-0307  
Model BSF1731 Shown  
 
PLEASE READ AND SAVE THESE  
IMPORTANT SAFEGUARDS.  
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC (Alternating Current) PLUG (a plug  
having one blade wider than the other). This plug will fit into the power outlet only one  
way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit,  
contact qualified personnel to install the proper outlet.  
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS POLARIZED PLUG IN ANY WAY.  
ASSEMBLY INSTRUCTIONS  
H
C
A
E
G
D
F
B
I
J
K
Figure 1  
BSF1731  
Q
A. Grill Hub  
B. Front Grill  
M
N
C. Fan Blade Nut  
D. Fan Blade  
E. Rear Grill  
Mounting-Ring  
F. Rear Grill  
G. Motor Shaft  
H. Motor Housing  
I. Upper Pole  
L
P
O
H
J. Height Adjustment Knob  
K. Lower Pole  
L. Base Insert  
G
T
M. Base  
N. Weighted Insert  
O. Weight Nut  
P. Fixed Screw  
R
I
S
Q. Grill Ring  
R. Remote Control Housing  
S. Fan Post Screw  
T. Remote Control  
J
Figure 2  
BSF1731RC  
K
BASE/POLE ASSEMBLY  
Step 1: Insert lower pole into the base until the threaded end of the pole  
protudes through the opening in the center of the base. Twist the pole  
clockwise until locked.  
Step 2: Turn the base upside down and place the weighted insert into  
the base by aligning it between the two parallel ribs. Secure the base,  
weight, and pole system together by tightening the weight nut to the  
threaded portion of the pole. Place the base on the floor, right side up.  
Step 3:Replace the height adjustment knob over the pole, slide it down  
the pole, and secure it to the base by turning clockwise.  
2
 
FAN HEAD ASSEMBLY  
TRIM CAP  
Figure 2  
Figure 4  
Figure 3  
Figure 5  
Step 1: Position the rear grill over the motor shaft, making  
certain the cut outs in the center of the grill fit over the prongs on the  
motor housing. Please make sure the rear grill fits securely against the  
motor housing.  
Step 2: Secure the rear grill in its place using the rear grill mounting-  
ring. Turn this ring clockwise and tighten firmly.  
Step 3: Slide the fan blade, with the hollowed interior of the blade fac-  
ing toward the rear grill, firmly onto the motor shaft. Make sure that the  
pin through the motor shaft aligns with the groove in the back center of  
the fan blade.  
Step 4: Secure the fan blade onto the motor shaft by firmly tightening  
the fan blade nut.  
NOTE: TURN THE FAN BLADE NUT COUNTER-CLOCKWISE  
Step 5: Align the tabs on the grills, and press grills firmly against each  
other. (Figure 2)  
Step 6: Place grill ring over attached front and rear grills with connect-  
ing link centered over the top of the grill. Make sure to fit the grooves  
on the underside of the grill ring over the edge of the front and rear  
grills. (Figure 3)  
Step 7: Secure the grill ring to the front and rear grills using the fixed  
screw. Place the trim cap over the connecting link and snap into place.  
(Figures 4 & 5)  
FINAL ASSEMBLY  
FOR REMOTE VERSION  
Step 1: Slide the remote control housing over the upper pole and  
secure the housing with the fan post screw.  
FINAL ASSEMBLY  
FOR NON-REMOTE VERSION  
Step 1: Slide the threaded end of the fan head pole, into the top of the  
pole. Holding the neck of the fan, turn it counterclockwise until it locks  
into position.  
NOTE: Make sure the top of the upper pole is facing away from you  
when placing the fan head into the pole.  
3
 
OPERATING INSTRUCTIONS  
FOR REMOTE VERSION  
Step 1: Insert 2 AAA batteries into the back of the remote control.  
Remote Control: Your remote control requires 2 AAA batteries for operation.  
To install the batteries, simply depress the back of the remote with your  
thumb on the spot marked OPEN. Insert batteries according to the diagram  
shown inside. Replace cover.  
Step 2: Set the fan base on a dry level surface.  
Step 3: Plug cord into any standard 120V AC outlet.  
Step 4: To turn the fan on press the POWER button on the remote control  
or on the touch-key pad.  
Step 5: The speed is adjustable by pushing either the speed button on the  
remote control, or on the SPEED button on the touch-key pad. Push this  
button first for LOW, again for MEDIUM, and a third time for HIGH. Push a  
fourth time to repeat the sequence. To turn the fan OFF, push the OFF  
button on the remote control, or on the touch-key pad.  
Step 6: To oscillate the fan head, push the button marked OSCILLATE on  
the remote, or OSCILLATE on the touch-key pad. Push a second time to  
stop oscillation.  
Step 7: This fan is equipped with a 4-setting timer. (1hr, 2hr, 4 hr, 8hr). To  
activate the timer, push the TIMER button on the remote control, or the  
TIMER button on the touch-key pad. Continue to push the TIMER button  
to cycle through your setting options. Push the button twice to repeat the  
sequence.  
Step 8: For a natural breeze movement, push the button marked MODE  
on the remote control or the touch-key pad. This BREEZE mode will imi-  
tate wind gust by varying the fan speeds between fast and slow. By  
pressing the MODE button a second time, you activate the SLEEP setting.  
This function slows the fan speed down, and when used in conjunction  
with the timer settings, will ultimately turn the fan off. Press the Mode  
button a 3rd time for BREEZE and SLEEP combined.  
NOTE: Timer can be used in conjunction with several other functions. For  
example: Sleep + 4hr. TIMER causes the fan to gradually slow down over  
4 hours and eventually turn off.  
OPERATING INSTRUCTIONS  
FOR NON-REMOTE VERSION  
Step 1: Set the fan base on a dry, level surface.  
Step 2: Please make sure the Speed Control Knob is in the "Off" position. Plug  
the cord into any standard 120 V A/C outlet.  
Step 3: The SPEED is adjusted by moving the knob left or right to the  
desired setting.  
Step 4: The OSCILLATION Knob is located on the top of the fan motor hous-  
ing. To start oscillation, push knob down. To stop oscillation, pull knob up.  
ADJUSTMENT INSTRUCTIONS  
TILT ADJUSTMENT  
Follow these instructions to tilt the fan head for upward angle  
air movement.  
Step 1: To change the tilting angle of the fan head, move the fan head to the  
desired position. This will work only on RC model On the non-remote,  
the customer needs to loosen the tilt adjustment knob first.  
4
 
HEIGHT ADJUSTMENT  
Step 1: Twist the height adjustment know counterclockwise and slide  
the fan up or down to the desired position and then tighten the knob.  
WARNING: MAKE SURE TO SUPPORT THE FAN HEAD  
ASSEMBLY WHEN ADJUSTING THE HEIGHT, AS THE  
WEIGHT OF THE FAN HEAD MAY CAUSE THE UPPER  
POLE TO COLLAPSE.  
CLEANING/MAINTENANCE INSTRUCTIONS  
Follow these instructions to correctly and safely care for your Bionaire®  
stand fan. Please remember:  
• Always unplug the fan before cleaning or disassembling.  
• Do not allow water to drip on or into the fan motor housing.  
• Do not use any of the following as a cleaner: gasoline, thinner, ben-  
zine.  
(See instructions for fan head assembly)  
Step 1: To access the fan blade, remove the front grill and the fan blade  
nut.  
Step 2: Clean the fan blade, both front and rear grills with a soft cloth  
moistened with a mild soap solution.  
Step 3: Replace blade, tighten the fan blade nut, and securely fasten  
the front grill.  
FAN HEAD, BASE, AND POLE CLEANING  
Using a soft, moist cloth, with or without a mild soap solution, carefully  
clean the fan base, pole, and head. Please use caution around the  
motor housing area. Do not allow the motor or other electrical compo-  
nents to be exposed to water.  
FAN STORAGE INSTRUCTIONS  
Your fan can be stored in the off-season either partially disassembled or  
assembled. It is important to keep it in a safe, dry location.  
• If stored disassembled, we recommend using the original (or appropri-  
ately sized) box.  
• If stored assembled or partially assembled, remember to protect the  
fan head from dust.  
FAN SERVICE INSTRUCTIONS  
1. Do NOT attempt to repair or adjust any electrical or mechanical func-  
tions on this unit. Doing so will void the warranty.  
2. If you have any questions regarding this unit’s operation or believe  
any repair is necessary, please call 1-800-788-5350 to speak with a  
consumer service representative.  
3. If you need to exchange the unit, please return it in its original carton,  
with a sales receipt, to the store where you purchased it. If you are  
returning the unit more than 30 days after the date of purchase, please  
see the enclosed warranty.  
 
5
WARRANTY  
Bionaire® warrants to the first retail purchaser, for FIVE (5) YEARS from the  
date of original purchase, either to repair or replace at its option, without  
charge (parts and labor), any supplied or manufactured part of this heater  
which, upon inspection by an authorized service center, proves to have  
failed in normal use due to defects in material or workmanship, or, at its  
option, to replace the unit.  
Operation under conditions other than those recommended or at voltages  
other than the voltage indicated on the unit, or any attempts by  
unauthorized personnel to service the unit or modify it, will render the  
guarantee void.  
Bionaire® shall not be liable for any personal injury, property damage or  
any incidental or consequential damages of any kind (including water  
damage), resulting from defects, malfunctions, misuse, improper  
installation or alteration of the product.  
BIONAIRE® EXPRESSLY DISCLAIMS ALL  
RESPONSIBILITY FOR CONSEQUENTIAL  
DAMAGES OR INCIDENTAL LOSSES  
CAUSED BY USE OF THIS PRODUCT.  
The provisions of this warranty are in addition to, and not a  
modification of, or subtraction from the statutory warranties  
and other rights and remedies contained in any applicable  
legislation and to the extent that any such provision purports  
to disclaim, exclude or limit any such statutory warranties or  
other rights or remedies, such provisions shall be deemed to be amended  
to the extent necessary to comply therewith.  
For Warranty Service, please call 1-800-788-5350  
in North America.  
A Bionaire® consumer service representative will help determine which is  
the best procedure in order for your fan to be repaired.  
KEEP THIS NUMBER FOR FUTURE REFERENCE.  
P.O. BOX 400  
MILFORD, MA 01757  
USA  
6385 Shawson Drive  
Mississaugua, Ontario  
Canada, L5T 1S7  
6
 
 

Bosch Appliances Home Security System VIP X2 User Manual
Bosch Appliances Water Heater W11P User Manual
Brocade Communications Systems Marine Radio 53 1002745 02 User Manual
Brookstone Automobile Accessories 643494 User Manual
Canon Camcorder 40MC User Manual
Carrier Ventilation Hood 62E User Manual
Cateye Cyclometer PW TR100 User Manual
Channel Vision Stereo Receiver A4603 User Manual
Char Broil Charcoal Grill 4651330 User Manual
Chromalox Thermostat PK413 4 User Manual